Forum PKP Gdynia - Wszystko o Polskiej Kolei Strona Główna

 coach diaper bag clearance Learn Ho coach diaper b

Zobacz poprzedni temat :: Zobacz następny temat
Napisz nowy temat   Odpowiedz do tematu
Autor Wiadomość

Dołączył: 25 Mar 2011
Posty: 22
Przeczytał: 0 tematów

Ostrzeżeń: 0/5
Skąd: England
Płeć: Kobieta

PostWysłany: Pon 8:39, 28 Mar 2011    Temat postu: coach diaper bag clearance Learn Ho coach diaper b

your Town Car is starting to hit the bumps a little hard in the front, or if the car is swerving a bit and feeling soft [link widoczny dla zalogowanych], you may need to replace those front shocks, especially if it has been a while. If you are mechanically inclined you should be able to do this job without any issues.
With the car in park and emergency brake on [link widoczny dla zalogowanych], set up your tire blocks behind the rear tires. If you have an active air suspension system, turn it off from the switch in the trunk. From under the hood, loosen the nut on the shock rod with your 9/16 hand wrench or deep well socket. Hopefully it turns easily and isn't frozen, which would not be unusual. If this is the case, you will need the "Optional" items mentioned. Try some Rust Buster spray and work with vice grips to hold the shock rod still if it turns with the nut. The worse case scenario should be having to use a nut splitter to split open the nut for removal.
Loosen the lug nuts on the tire; jack the car up high enough to fully remove the tire. Set up a jack stand under the frame of the car on the side you will be working on, but not too near to the bottom of the shock, since you need this area clear. Never rely on a floor jack to carry the load of the car when you will be under it.
Put on your safety glasses to avoid any debris from getting into your eyes while under the car looking up. Set up lighting under the car and then loosen the 2 shock mounting bolts. They should loosen up easily with your 9/16 socket or hand wrench. Once they are completely out, remove the shock from the bottom of the car.
To install the new shock [link widoczny dla zalogowanych], slide a metal cup down the shock rod, bowl side facing upwards, and follow it with a rubber bushing, making sure that the metal cup embraces the rubber bushing within it's bowl shape. Now feed the shock up from the bottom of the car and hold the bottom of the shock upward onto the mounting surface as you tighten the 2 bolts.
Going back under the hood, slide the second rubber bushing and metal cup to follow, over the shock rod, making sure the rubber bushing is sitting flush on top of the mounting tower with the metal cup embracing the bushing, and then tighten down the nut until the shock rod begins to turn with the nut.
Put your tire back on, remove your jack and stand, then follow the same steps for removal and installation for the other side.

Post został pochwalony 0 razy
Powrót do góry
Zobacz profil autora
Wyświetl posty z ostatnich:   
Napisz nowy temat   Odpowiedz do tematu    Forum PKP Gdynia - Wszystko o Polskiej Kolei Strona Główna -> Administracja Wszystkie czasy w strefie EET (Europa)
Strona 1 z 1

Skocz do:  
Nie możesz pisać nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz głosować w ankietach - załóż własne forum dyskusyjne za darmo
Powered by phpBB © 2001, 2005 phpBB Group
gBlue v1.3 // Theme created by Sopel & Programosy